staticconstuint16_tNR_ACTION_NOT_SUPPORTED=0x000B;//!< The specified action is not supported.
staticconstuint16_tNR_UNKNOWN_SCOPE=0x000F;//!< The Component is not participating in the given Scope.
staticconstuint16_tNR_INVALID_STATIC_CONFIG_TYPE=0x0010;//!< The Static Config Type provided is invalid.
staticconstuint16_tNR_INVALID_IPV4_ADDRESS=0x0011;//!< The IPv4 Address provided is invalid.
staticconstuint16_tNR_INVALID_IPV6_ADDRESS=0x0012;//!< The IPv6 Address provided is invalid.
staticconstuint16_tNR_INVALID_PORT=0x0013;//!< The transport layer port provided is invalid.
/// A.17 Static Config Type for COMPONENT_SCOPE Parameter Message
staticconstuint8_tNO_STATIC_CONFIG=0x00;//!< No Broker Static Configuration is present; the Client shall locate a Broker via DNS-SD.
staticconstuint8_tSTATIC_CONFIG_IPV4=0x01;//!< A Static Configuration exists for locating a Broker via IPv4.
staticconstuint8_tSTATIC_CONFIG_IPV6=0x02;//!< A Static Configuration exists for locating a Broker via IPv6.
/// A.18 Broker State Definitions for BROKER_STATUS Parameter Message
staticconstuint8_tBROKER_DISABLED=0x00;//!< The Broker has been disabled through either a SET: BROKER_STATUS command or some implementation-defined method.
staticconstuint8_tBROKER_ACTIVE=0x01;//!< The Broker is running normally and has successfully registered its DNS-SD subtype.
staticconstuint8_tBROKER_STANDBY=0x02;//!< The Broker has detected another Broker registered with its scope and is waiting for this condition to be resolved before continuing operation.
/// A.19 Connection Status Codes for Broker Connect
staticconstuint8_tLLRP_COMPONENT_TYPE_RPT_DEVICE=0x00;//!< The LLRP Target is a Device
staticconstuint8_tLLRP_COMPONENT_TYPE_RPT_CONTROLLER=0x01;//!< The LLRP Target is a Controller
staticconstuint8_tLLRP_COMPONENT_TYPE_BROKER=0x02;//!< The LLRP Target is a Broker
staticconstuint8_tLLRP_COMPONENT_TYPE_NON_RDMNET=0xFF;//!< The LLRP Target does not implement any RDMnet protocol other than LLRP
/// A.24 Client Disconnect Reason Codes
staticconstuint16_tDISCONNECT_SHUTDOWN=0x0000;//!< Comment Sent by Components to indicate that they are about to shut down.
staticconstuint16_tDISCONNECT_CAPACITY_EXHAUSTED=0x0001;//!< Sent by Components when they do not have the ability to support this connection. Note that a Component must reserve certain resources to be able to send this message when it is in such a state.
staticconstuint16_tDISCONNECT_HARDWARE_FAULT=0x0002;//!< Sent by Components which must terminate a connection due to an internal hardware fault.
staticconstuint16_tDISCONNECT_SOFTWARE_FAULT=0x0003;//!< Sent by Components which must terminate a connection due to a software fault.
staticconstuint16_tDISCONNECT_SOFTWARE_RESET=0x0004;//!< Sent by Components which must terminate a connection because of a software reset. This message should not be sent in the case of a reboot, as the Shutdown message is preferred.
staticconstuint16_tDISCONNECT_INCORRECT_SCOPE=0x0005;//!< Sent by Brokers that are not on the desired Scope.
staticconstuint16_tDISCONNECT_RPT_RECONFIGURE=0x0006;//!< Sent by Components which must terminate a connection because they were reconfigured using RPT.
staticconstuint16_tDISCONNECT_LLRP_RECONFIGURE=0x0007;//!< Sent by Components which must terminate a connection because they were reconfigured using LLRP.
staticconstuint16_tDISCONNECT_USER_RECONFIGURE=0x0008;//!< Sent by Components which must terminate a connection because they were reconfigured through some means outside the scope of this standard (i.e. front panel configuration)