diff --git a/wiflash_esp32/wiflash_esp32.ino b/wiflash_esp32/wiflash_esp32.ino
index 93f0c30..b53ef60 100644
--- a/wiflash_esp32/wiflash_esp32.ino
+++ b/wiflash_esp32/wiflash_esp32.ino
@@ -26,11 +26,13 @@
   SOFTWARE.
 */
 
+#include <Arduino.h>
 #include <WiFi.h>
 #include "sacn.h"
 #include <ArduinoOSC.h>
 #include "strobe_esp32.h"
-
+#include "dmx_universe.h"
+#include <NeoPixelBus.h>
 
 /*
    This section to be configured by Lighting Control
@@ -62,6 +64,8 @@ const String released_value = "99.2";
 //   Configure E1.31 sACN
 // -----------------------------------
 const e131_listen_t sACN_mode  = E131_UNICAST;  // (uni|multi)cast
+const uint16_t pixel_universe  = 1;
+const uint16_t pixel_address   = 001;
 const uint16_t strobe_universe = 1;
 const uint16_t strobe_address  = 501;
 
@@ -84,6 +88,9 @@ const uint16_t strobe_address  = 501;
 const int button = A0;        // A0, use 100nF to ground
 const int led = LED_BUILTIN;  // IO13
 
+const uint16_t       PixelCount  = 8;  // not less than 4
+const uint8_t        PixelPin    = 21; // make sure to set this to the correct pin
+NeoPixelBus<NeoGrbwFeature, Neo800KbpsMethod> strip(PixelCount, PixelPin);
 
 /*
    Change nothing else unless you're really sure.
@@ -97,6 +104,21 @@ ESPAsyncE131 *e131 = new ESPAsyncE131();
 bool pressed = false;    // track button state
 uint32_t change_time;    // time of button press (ms)
 
+
+
+void recvPixelData(Universe *universe) {
+  for (int i = 0; i < PixelCount; i++) {
+    uint8_t r, g, b, w;
+    r = universe->data()->data[pixel_address + (i * 4) + 0];
+    g = universe->data()->data[pixel_address + (i * 4) + 1];
+    b = universe->data()->data[pixel_address + (i * 4) + 2];
+    w = universe->data()->data[pixel_address + (i * 4) + 3];
+    strip.SetPixelColor(i, RgbwColor(r, g, b, w));
+  }
+  strip.Show();
+}
+
+
 /*
    Arduino powerup
 */
@@ -123,16 +145,15 @@ void setup() {
     Serial.println("STA Failed to configure");
   }
 
-
   //// start sACN
-  if (!e131->subscribe(strobe_universe, sACN_mode)) {
-    Serial.println("Failed to start E1.31");
-  } else {
+  if (e131->subscribe(strobe_universe, sACN_mode)) {
     e131->universe(strobe_universe)->onData(std::bind(&Strobe::recvData,
                                             strobe, std::placeholders::_1));
-    Serial.println("Listening for sACN");
   }
-
+  if (e131->subscribe(pixel_universe, sACN_mode)) {
+    e131->universe(pixel_universe)->onData(std::bind(&recvPixelData,
+                                           std::placeholders::_1));
+  }
 
   //// start fixtures hardware:
   // button
@@ -140,6 +161,9 @@ void setup() {
   if (!strobe->begin(led, 0)) {
     Serial.println("Strobe failed to configure.");
   }
+  // pixels
+  strip.Begin();
+  strip.Show();
 }